Gnee Steel (Tianjin) Co., Ltd.

Copper Flat Wire Dimensions and Tolerances

Nov 10, 2026

Copper Flat Wire Dimensions Explained

Copper flat wire has a rectangular or approximately rectangular cross-section. Its dimensions are mainly defined by width and thickness.

 

Width, Thickness, and Cross-Sectional Area

The main dimensional parameters are:

Width (W): The wider side of the rectangular cross-section.

Thickness (T): The smaller side of the cross-section.

Edge Radius (R): The radius of rounded corners, when specified.

Length (L): The supplied length, either in coils or straight sections.

 

Copper Flat Wire Width, Thickness and Cross-Sectional Dimensions

Copper Flat Wire Width

 

For a rectangular cross-section with square corners, the nominal cross-sectional area is calculated using the following formula:

Cross-Sectional Area = Width × Thickness

A = W × T

 

Where:

A = Cross-sectional area (mm²)

W = Width (mm)

T = Thickness (mm)

 

Example:

For copper flat wire with a width of 10 mm and a thickness of 2 mm:

A = 10 × 2 = 20 mm²

The nominal cross-sectional area is 20 mm².

 

For rounded-edge products, the actual cross-sectional area may be slightly different from the simple width × thickness calculation. The specified edge profile should therefore be considered when precise area calculations are required.

 

Common Copper Flat Wire Dimensions

Copper flat wire is available in different width and thickness combinations depending on the application and manufacturing process.

The following combinations are examples of possible product specifications, not a universal standard size range.

Width (mm) Thickness (mm) Cross-Sectional Area (mm²)
5 1 5
6 2 12
8 2 16
10 2 20
10 3 30
12 2 24
15 3 45
20 3 60
20 5 100

Actual availability depends on copper grade, temper, production equipment, and required tolerances.

Custom widths and thicknesses can be discussed according to the buyer's drawings and application requirements.

 

Copper Flat Wire in Coils and Straight Lengths

Copper flat wire is generally supplied in coils or straight lengths.

Supply Form Characteristics Typical Requirements
Coils Continuous material wound onto reels or bobbins Coil weight, inner diameter, outer diameter, winding condition
Straight Lengths Cut into specified lengths Length tolerance, straightness, end condition
Custom Bobbin Packaging Wound onto industrial or customer-specified bobbins Flange diameter, drum width, bore diameter, maximum coil weight

 

Bare Copper Flat Wire Wound on a Custom Industrial Bobbin

Bare Copper Flat Wire 

 

Copper Flat Wire Dimensional Tolerances

Dimensional tolerance refers to the permitted variation between the nominal dimensions specified by the buyer and the actual dimensions of the delivered product.

For copper flat wire, the main dimensional tolerances generally include width, thickness, length, straightness, and edge contour.

 

Width Tolerance

Width tolerance controls how much the actual width can deviate from the nominal width.

 

For example, if the specified width is 10 mm with a tolerance of ±0.10 mm, the acceptable width range is:

Minimum width: 9.90 mm

Nominal width: 10.00 mm

Maximum width: 10.10 mm

 

The actual tolerance must be agreed upon according to the applicable product specification and manufacturing requirements.

Width accuracy is particularly important for copper flat wire used in winding assemblies, electrical connections, and components with limited installation space.

 

Thickness Tolerance

Thickness tolerance controls the variation in the smaller dimension of the rectangular conductor.

For example, a copper flat wire with a nominal thickness of 2.00 mm and a tolerance of ±0.05 mm has an acceptable thickness range of 1.95–2.05 mm.

 

Thickness variation can affect:

Cross-sectional area

Electrical resistance

Winding space requirements

Contact and assembly dimensions

Material weight per unit length

 

For applications requiring consistent electrical and mechanical performance, buyers should specify both nominal thickness and permitted thickness variation.

 

Dimensional Tolerance Reference

ASTM B272-12(2019), Standard Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip), covers dimensional requirements including thickness, width, length, straightness, and edge contour.

The standard covers several copper grades, including C10100, C10200, C11000, and C12200.

 

However, the applicable tolerance must be determined from the relevant standard requirements, product dimensions, and agreed purchase specification. A single tolerance value should not be applied to every copper flat wire size.

 

For procurement purposes, buyers can use the following table to define their requirements:

Parameter Nominal Specification Tolerance Requirement
Width 10.00 mm ±0.10 mm
Thickness 2.00 mm ±0.05 mm
Length 2,000 mm ±2 mm
Edge Radius As specified According to drawing
Straightness As specified According to drawing or agreement

The values above are illustrative RFQ examples, not ASTM B272 tolerance limits.

 

Copper Flat Wire Edge Types and Their Dimensional Differences

Edge configuration is another important part of copper flat wire specifications.

Different edge profiles can affect the actual cross-section, handling, winding performance, and installation compatibility.

 

Square Edge

Square-edge copper flat wire has relatively sharp corners and a rectangular cross-section.

Typical characteristics:

Flat upper and lower surfaces

Defined rectangular corners

Suitable for applications requiring a specified rectangular profile

 

Rounded Edge

Rounded-edge copper flat wire has curved corners instead of sharp 90-degree edges.

Typical characteristics:

Reduced sharpness at the corners

Specified edge radius where required

Useful in winding applications where corner geometry matters

 

Deburred Edge

Deburred copper flat wire has had sharp burrs removed from its edges during processing.

Typical characteristics:

Reduced risk of sharp projecting edges

Improved handling safety

More consistent edge condition

Deburred edges and rounded edges are not necessarily the same. Removing burrs does not automatically produce a defined corner radius.

 

Copper Flat Wire Edge Profiles

Copper Flat Wire Edge Profiles

 

Copper Flat Wire Dimensions for Different Applications

Different applications require different dimensional combinations. Buyers should select the dimensions according to electrical requirements, installation space, winding design, and mechanical conditions.

Application Important Dimensions Main Purchasing Considerations
Transformer Windings Width and thickness Winding space, dimensional consistency, insulation requirements
Motor Windings Width, thickness, and edge radius Slot dimensions, winding arrangement, corner condition
Electrical Conductors Cross-sectional area Current-carrying requirements and electrical resistance
Busbar Connections Width and thickness Contact area, connection dimensions, and installation space
Electromagnetic Equipment Custom dimensions Drawing compatibility and dimensional repeatability

 

Transformer and Motor Winding Applications

For winding applications, the width and thickness of copper flat wire must match the available winding space.

 

Buyers should pay attention to:

Nominal width and thickness

Dimensional consistency

Edge configuration

Required temper

Insulation or coating requirements, if applicable

 

For enamelled rectangular winding wire, additional requirements such as insulation thickness and finished conductor dimensions must be considered separately.

 

Electrical Conductors and Busbar Connections

For electrical conductors, cross-sectional area is an important selection parameter.

 

For a rectangular copper conductor:

Cross-Sectional Area = Width × Thickness

A = W × T

 

For example, a conductor measuring 20 mm in width and 3 mm in thickness has a nominal cross-sectional area of:

A = 20 × 3 = 60 mm²

 

However, two conductors with the same cross-sectional area may have different widths and thicknesses.

Therefore, buyers should not select copper flat wire based on cross-sectional area alone. The actual dimensions must also match the equipment design and installation requirements.

 

Relevant Standards for Copper Flat Wire Dimensions

Different standards cover different copper product forms and applications. Buyers should confirm that the selected standard matches the actual product.

Standard Scope Relevance
ASTM B272 Copper flat wire and strip with finished rolled or drawn edges Relevant to general copper flat products
IEC 60317-0-2 Particular requirements for enamelled rectangular copper winding wire Relevant to insulated winding wire
ASTM B193 Resistivity testing of electrical conductor materials Relevant to electrical material testing

Important distinction: ASTM B272 is a relevant reference for bare copper flat wire with finished edges. IEC 60317-0-2 is specifically for enamelled rectangular winding wire and should not be used as a general tolerance specification for bare copper flat wire.

 

For example, IEC 60317-0-2 includes defined dimensional tolerance tables for enamelled rectangular winding wire. These values apply within the scope of that standard and should not be transferred directly to products supplied under ASTM B272.

 

How to Specify Copper Flat Wire Dimensions in an RFQ

Item Information to Provide Example
Copper Grade UNS grade or equivalent C11000
Width Nominal width 10 mm
Thickness Nominal thickness 2 mm
Width Tolerance Permitted variation ±0.10 mm
Thickness Tolerance Permitted variation ±0.05 mm
Edge Type Required edge profile Rounded Edge
Temper Material condition Annealed
Supply Form Delivery form Coil
Coil Weight Required weight per coil According to requirement
Applicable Standard Product specification ASTM B272
Quantity Order quantity 1,000 kg

 

FAQ

Q: What are the standard dimensions of copper flat wire?

A: Copper flat wire is manufactured in different width and thickness combinations. There is no single universal dimension range covering every copper flat wire product.
The available dimensions depend on the copper grade, temper, production process, and applicable specification.

Q: What is the thickness tolerance of copper flat wire?

A: Thickness tolerance depends on the product standard, nominal thickness, manufacturing method, and buyer requirements.
For precision applications, buyers should specify the permitted thickness deviation in the purchase order or technical drawing.

Q: Can copper flat wire be manufactured to custom widths and thicknesses?

A: Yes. Custom dimensions can be discussed according to the required copper grade, temper, production capabilities, and quantity.
Buyers should provide the nominal width, thickness, tolerances, and application details for evaluation.

Q: How do you measure copper flat wire thickness?

A: An outside micrometer is commonly used to measure copper flat wire thickness. Measurements should be taken at suitable positions along the sample to check dimensional consistency.

Q: What is the difference between square-edge and rounded-edge copper flat wire?

A: Square-edge copper flat wire has relatively sharp rectangular corners, while rounded-edge copper flat wire has curved corners with a specified or agreed radius.
The appropriate edge profile depends on the application and drawing requirements.

Q: Can copper flat wire be supplied in coils or straight lengths?

A: Yes. Supply forms can include continuous coils, industrial bobbins, and straight-cut lengths.
Buyers should specify the required delivery form, coil weight, bobbin dimensions, or cut length.

Q: Which ASTM standard applies to copper flat wire?

A: ASTM B272 covers copper flat products with finished rolled or drawn edges, including flat wire and strip.
The buyer should confirm the applicable edition and product requirements when preparing the purchase order.

Request a Quote for Copper Flat Wire

Selecting the correct copper flat wire requires matching the material grade, dimensions, tolerances, edge profile, and delivery requirements to the intended application.

As a copper material supplier, we can discuss different copper grades, tempers, dimensional combinations, and customized supply forms according to customer requirements.

 

To receive a quotation, please provide:

Copper grade: C11000, C10200, C10100, or other required grades

Width and thickness

Required dimensional tolerances

Edge configuration

Annealed or hard temper

Coil or straight-length requirements

Order quantity

Applicable standards or technical drawings

 

Have a specific copper flat wire specification? Send us your drawings or RFQ. We can review your requirements and discuss suitable material, dimensions, tolerances, and delivery options.

goTop