Gnee Steel (Tianjin) Co., Ltd.

copper rod

Jul 30, 2024

What is copper rod?

info-275-183Firm discovers copper deposits | Nation OnlineHow to invest in copper: A comprehensive guide | CNN Underscored Money

The main purpose of copper rod is as raw material for the production of wires and cables. It can be roughly divided into: low-oxygen copper rod and oxygen-free copper rod. It is mainly used in power, construction, home appliances, automobiles, electronics and other industries.

The raw materials for copper rod production are mainly electrolytic copper or scrap copper. There are two main production processes: continuous casting and rolling method and up-casting method.

The up-casting method can produce oxygen-free copper rods; continuous casting and rolling can only produce low-oxygen copper rods. Due to the different raw materials and processes for producing copper rods, the oxygen content and appearance of the copper rods produced are different.

Low-oxygen copper rod: Copper rods produced by continuous casting and rolling have an oxygen content in the range of 200-450ppm

Oxygen-free copper rod: Copper rods produced by up-casting method have an oxygen content below 20ppm

Although it is called oxygen-free copper rod, it actually contains very trace amounts of oxygen and some impurities. According to the standard, the oxygen content is not more than 0.003%, the impurity content is not more than 0.05%, and the purity of copper is greater than 99.95%.

Difference between oxygen-free copper rod and low-oxygen copper rod

1

Grade

Low-oxygen copper rod: The grades of low-oxygen copper rod are: T1, T2, T3; State: hot-rolled (M20).

T1: Low-oxygen copper rod produced with high-purity electrolytic copper as raw material (copper content greater than 99.9975%)

T2: Low-oxygen copper rod produced with 1# electrolytic copper as raw material (copper content greater than 99.95%)

T3: Low-oxygen copper rod produced with 2# electrolytic copper as raw material (copper content greater than 99.90%)

(Figure: high-purity electrolytic copper)

Oxygen-free copper rod: There are two grades of oxygen-free copper rod, TU1 and TU2.

TU1: Oxygen-free copper rod produced with high-purity electrolytic copper as raw material, copper purity reaches 99.99%, oxygen content is not more than 0.001%.

TU2: Oxygen-free copper rod produced with 1# electrolytic copper, copper purity reaches 99.95%, oxygen content is not more than 0.002%.

2

Production process

The production process of low-oxygen copper rod is that after the metal is melted in the vertical furnace, the copper liquid passes through the insulation furnace, chute, and tundish, and enters the closed mold cavity from the pouring pipe, and is cooled with a large cooling intensity to form a cast billet, and then multiple rolling is performed.

The production process of oxygen-free copper rod is that after the metal is melted in the induction furnace, it is continuously cast through a graphite mold, and then cold rolled or cold processed.

(Figure: Upward process)

3

Organization structure

Low-oxygen copper rod Since the low-oxygen copper rod has been hot-rolled, its organization belongs to the hot processing organization. The original casting organization has been broken, and recrystallization has appeared in the 8mm rod. From the organizational point of view, the oxygen in the low-oxygen copper rod exists near the grain boundary in the form of copper oxide.

Oxygen-free copper rods are cast structures with coarse grains and grain sizes that can even reach several millimeters, so there are few grain boundaries. The successful annealing requirements for oxygen-free copper are: the first annealing when the rod is drawn but has not yet cast the structure line should be 10-15% higher than the low-oxygen copper in the same situation.

4

Oxygen content

The oxygen content of low-oxygen copper rods is generally 200 (175)-400 (450) ppm, so oxygen is absorbed in the liquid state of copper. The oxygen content of good copper rods is generally controlled at around 250ppm.

The oxygen content of oxygen-free copper rods is below 10-20ppm, but many copper bar manufacturers can only achieve below 50ppm. After being kept in the liquid state of copper for a long time, the oxygen is recovered and removed. Usually, the oxygen content of this rod is below 10-50ppm, and can even be as low as 1-2ppm. Due to the low oxygen content, the structure is a uniform single-phase structure, which is conducive to toughness.

However, if the oxygen content of oxygen-free copper rod exceeds the standard, the copper rod will become brittle, the elongation will decrease, the end of the stretched pattern will appear dark red, and the crystal structure will be loose. This is because oxygen can generate cuprous oxide brittle phase with copper, forming copper-cuprous oxide eutectic, which is distributed on the boundary in a network structure.

This brittle phase has high hardness and will separate from the copper body during cold deformation, resulting in a decrease in the mechanical properties of the copper rod and easy fracture in subsequent processing. High oxygen content can also lead to a decrease in the conductivity of oxygen-free copper rods. Therefore, the upward continuous casting process and product quality must be strictly controlled.

5

Impurity content

During the production process, the continuous casting and rolling process needs to transfer copper liquid through the insulation furnace, chute, and tundish, which is relatively easy to cause the peeling of refractory materials. During the rolling process, it needs to pass through the roller, causing the iron to fall off, which will bring external inclusions. The rolling of oxides in the process has an adverse effect on the wire drawing of low-oxygen rods.

The production process of the upward continuous casting method is relatively short. The copper liquid is completed by the submerged flow in the joint furnace, which has little impact on the refractory material. The crystallization is carried out in the graphite mold, so there are fewer pollution sources that may be generated in the process and fewer opportunities for impurities to enter.

(Figure: Melting furnace)

6

Drawing performance

The drawing performance of the copper rod is related to many factors, such as impurity content, oxygen content and distribution, process control, etc. The softness, rebound angle and winding performance of the oxygen-free copper rod are better than those of the low-oxygen copper rod.

Generally, when drawing copper wires with a diameter of >1mm, the advantages of low-oxygen copper rods are more obvious, and oxygen-free copper rods are more superior when drawing copper wires with a diameter of <0.5mm.

When drawing low-oxygen rods, it is difficult to draw filaments below 0.5mm. However, the spacing between the filaments of low-temperature oxygen-free copper in low-temperature superconducting wires can reach 0.001mm.

7

Surface quality

In the process of producing products such as electromagnetic wires, requirements are also required for the surface quality of copper rods. The copper wire surface after drawing needs to be free of burrs, less copper powder, and no oil stains, and the quality of the copper powder on the surface is measured by torsion test and the recovery of the copper rod is observed after torsion to determine its quality.

During the continuous casting and rolling process, from casting to before rolling, the temperature is high and it is completely exposed to the air, so that a thicker oxide layer is formed on the surface of the ingot. During the rolling process, as the rollers rotate, the oxide particles are rolled into the surface of the copper wire.

Since cuprous oxide is a brittle compound with a high melting point, for cuprous oxide that is rolled deeper, when the strip-shaped aggregates are stretched by the mold, burrs will be generated on the outer surface of the copper rod, causing trouble for subsequent painting.

The oxygen-free copper rod manufactured by the upper continuous casting process is completely isolated from oxygen during casting and cooling, and there is no subsequent hot rolling process. There is no oxide rolled into the surface of the copper rod, the quality is better, and there is less copper powder after drawing. Therefore, when encountering two products at the same time, the oxygen-free copper rod is generally brighter.

8

Applications

Low-oxygen copper rods and oxygen-free copper rods are both used in the following fields: wires and cables, enameled wires, flat wires, and copper bars.

Oxygen-free copper rods are produced with electrolytic copper, and their resistivity and processing performance are better than those of low-oxygen copper rods. Oxygen-free copper rods are generally used to produce electrical materials with high requirements. For example, when making enameled wires, oxygen-free copper rods have lower resistance, and when used in motors, they are definitely better than low-oxygen copper rods in terms of heating.

Therefore, low-oxygen rods are basically used for electrical products with large specifications and low resistance requirements, while oxygen-free rods are used for small specifications and high resistance requirements. On the contrary, speaker cables generally prefer oxygen-free rods, which is related to the fact that oxygen-free rods are single crystal copper and low-oxygen rods are polycrystalline copper.

9

Price

Since oxygen-free copper rods have so many advantages, the cost should be very high, right? The answer is definitely no.

At present, the main method used to make oxygen-free copper rods in China is the up-drawing method. This mainstream process itself has the advantages of short process flow, high yield rate, low cost, and low investment, so the price of oxygen-free copper rods is not much higher than that of ordinary copper rods;

The oxygen-free copper production process has undergone nearly 20 years of development, and there have been many improvements in operation methods and processes, such as adding a refining process to the up-drawing production process, and using the up-drawing power frequency furnace to melt the waste copper wire produced during the production process, eliminating additional processing fees and transportation fees.

goTop