CuZn15 ( CW502L )
| Grade : | CuZn15 |
| Number: | CW502L |
| Classification: | Copper-zinc alloy |
| Density | 8.8 g/cm ³ |
| Standard: | EN 1652: 1998 Copper and copper alloys. Plate, sheet, strip and circles for general purposes EN 12163: 1998 Copper and copper alloys. Rod for general purposes EN 12166: 1998 Copper and copper alloys. Wire for general purposes EN 12449: 1999 Copper and copper alloys. Seamless, round tubes for general purposes EN 1654: 1998 Copper and copper alloys. Strip for springs and connectors EN 13148: 2001 Copper and copper alloys. Hot-dip tinned strip |
| Equivalent grades: | Go here |
Chemical composition % of grade CuZn15 ( CW502L )
| Fe | Ni | Al | Cu | Pb | Sn | Others | - |
| max 0.05 | max 0.3 | max 0.02 | 84 - 86 | max 0.05 | max 0.1 | total 0.1 | Zn - remainder |
Mechanical properties of grade CuZn15 ( CW502L )
| Rm - Tensile strength (MPa) (R260) | 260-310 |
| Rm - Tensile strength (MPa) (R300) | 300-370 |
| Rm - Tensile strength (MPa) (R350) | 350-420 |
| Rp0.2 0.2% proof strength (MPa) (R260) | 170 |
| Rp0.2 0.2% proof strength (MPa) (R300) | 150 |
| Rp0.2 0.2% proof strength (MPa) (R350) | 250 |
| A - Min. elongation at fracture (%) (R260) | 45 |
| A - Min. elongation at fracture (%) (R300) | 25 |
| A - Min. elongation at fracture (%) (R350) | 12 |
| A - Min. elongation Lo = 50mm (%) (R260) | 36 |
| A - Min. elongation Lo = 50mm (%) (R300) | 16 |
| A - Min. elongation Lo = 50mm (%) (R350) | 4 |
| Vickers hardness ( HV): (H055) | 55 - 85 |
| Vickers hardness ( HV): (H085) | 85 - 115 |
| Vickers hardness ( HV): (H105) | 105 - 135 |
Properties CuZn15
| Modulus of elasticity = 120 kN/mm ² Electrical conductivity = 22 MS/m; |
Equivalent grades of grade CuZn15 ( CW502L )
Warning! Only for reference
| EU EN |
Germany DIN,WNr |
Russia GOST |
|||
| CuZn15 |
|
|
Casting process
| GS | Sand casting |
| GM | Permanent mould casting |
| GZ | Centrifugal casting |
| GC | Continuous casting |
| GP | Pressure die casting |
Material conditions
| R | Material condition designated by the minimum value of tensile strength requirement for the product with mandatory tensile strength and elongation requirements |
| H | Material condition designated by the minimum value of hardness requirement for the product with mandatory hardness requirements |
Mechanical properties
| ReH | Minimum yield strength / Mindestwert der oberen Streckgrenze / Limite d elasticite minimale |
| Rm | Tensile strength / Zugfestigkeit / Resistance a la traction |
| A | Minimum elongation / Mindestwert der Bruchdehnung / Allongement minimal |
| J | Notch impact test / Kerbschlagbiegeversuch / Essai de flexion par choc |
|
CuZn15 ( CW502L ) Copper-zinc alloy |
