What a TA1 Titanium Foil Roll Is
A TA1 titanium foil roll is thin-gauge unalloyed titanium delivered as a continuous coil for customers who need to run the material through forming, stamping, photo-etching or winding equipment without intermediate handling. TA1 is the softest and most ductile grade in the unalloyed titanium family used in production rolling, and it corresponds chemically to the commercially pure Grade 1 material of ASTM B265 / ASME SB-265. Chinese rolled foil and strip in this grade are produced to GB/T 3622, while heavier sheet and plate fall under GB/T 3621.
The grade is defined by impurity ceilings rather than by alloying additions, so the purchase decision turns on chemistry control, thickness tolerance and surface cleanliness. A mill certificate should state grade, governing standard, delivery condition and heat number, for example TA1 produced to GB/T 3622 in the annealed condition.
Chemistry and Mechanical Properties
The titanium content is the balance, with iron held to 0.20 % maximum, carbon to 0.08 %, nitrogen to 0.03 %, hydrogen to 0.015 % and oxygen to 0.18 %. Those limits sit in the same range used for ASTM Grade 1, which is why a TA1 foil and a Grade 1 foil are usually treated as technically interchangeable.
| Property | TA1 / Grade 1 annealed |
|---|---|
| Titanium | balance |
| Iron | 0.20 % max |
| Oxygen | 0.18 % max |
| Nitrogen / carbon / hydrogen | 0.03 % / 0.08 % / 0.015 % max |
| Tensile strength | about 240 MPa minimum |
| 0.2 % yield strength | roughly 138 to 310 MPa |
| Elongation | 24 % minimum |
Those modest strength figures are the point of the grade. Foil in this condition bends, deep draws and rolls without the springback and edge cracking that higher-strength titanium alloys show, and it keeps useful ductility down to cryogenic service.
Thickness, Width and Delivery Condition
Foil is generally understood as rolled titanium below 0.20 mm thick, and production coils run from roughly 0.01 mm up to that boundary, with strip continuing above it. Narrow slitting from a few millimetres supports precision stamped parts, while wider coils up to about 1,250 mm suit continuous process lines. Coil inner diameters of 300 mm, 400 mm and 500 mm are common, and coil weight and outside diameter are agreed against the customer's uncoiler.
Delivery condition is normally annealed for maximum formability, with bright, pickled or as-rolled surface finishes available. Edges may be slit, trimmed or deburred. Thin gauges are wound under controlled tension, and interleaving can be specified where creasing would be a rejection criterion.
Applications Across Process Industries
Plate heat exchanger foils take advantage of the corrosion resistance and forming behaviour, and electrolysis or electrode substrates use the stable surface film. Electronic shielding, battery and capacitor components use the low density together with consistent thickness. Chemical process equipment, aerospace brackets and consumer hardware also draw on the grade where a light, weldable and readily formed metal is needed.
Because titanium forms its protective oxide film spontaneously in air, the foil resists many oxidising and mildly reducing chemical environments. Chloride-bearing duties should still be reviewed against the specific concentration, temperature and aeration of the process, since that combination governs the actual corrosion allowance.
Inspection, Packaging and Certification
Roll to roll inspection covers thickness across the width, flatness, edge quality, surface defects and coil integrity. Chemistry is verified by certified analysis of each heat, and mechanical properties are confirmed on samples taken from the finished coil or from a representative test piece. Hardness and grain size are useful additional checks when the foil will be deep drawn or photo-etched.
Imported titanium is routinely released against an EN 10204 3.1 inspection certificate showing heat number, chemical composition, mechanical results and the standard of manufacture. Where traceability matters, the certificate heat number must be reconcilable with the coil marking and packaging label on delivery.
Frequently Asked Questions
Q: What thickness range is available for a TA1 titanium foil roll?
A: Foil is produced from about 0.01 mm to the 0.20 mm boundary, and the same grade continues as strip above that thickness, so a single order can cover both gauges from one melting source.
Q: Is TA1 the same as ASTM Grade 1 titanium?
A: The impurity ceilings are technically equivalent, so TA1 is normally accepted against ASTM B265 Grade 1 requirements. The certificate should name the standard and edition used for the release test.
Q: Can TA1 foil be welded or brazed?
A: Yes. Unalloyed titanium welds cleanly when the joint is protected from air by inert shielding, and brazing is possible with suitable filler selection, though heat tint must be removed before service in corrosive duties.
Q: How is the foil protected during shipping?
A: Coils are wound with interleaving where specified, wrapped against moisture and supported on a pallet or cradle so the coil face is not damaged in transit.
Q: What surface finishes can be supplied?
A: Bright annealed, pickled and as-rolled finishes are all produced. The choice is normally driven by the subsequent forming or etching operation rather than by appearance.







