Gnee Steel (Tianjin) Co., Ltd.

Copper Strip vs Brass Strip: Composition and Applications

Dec 08, 2025

Composition: What Separates the Two Strips

Copper strip, sometimes called electrolytic copper strip, is rolled from pure copper with a purity generally above 99.9 %, corresponding to grades such as T2 in GB/T 5231 or C11000 in UNS. Its defining characteristic is the high electrical and thermal conductivity that comes from that purity. Chemically the metal is stable, oxidising only gradually to a green patina in moist environments and remaining essentially unchanged otherwise.

Brass strip is a copper-zinc alloy. Properties depend on the zinc content, and in commercial strip the copper content is generally between 55 % and 70 % with zinc between 30 % and 45 %. Compared with copper strip, brass strip has better mechanical working properties and wear resistance but is clearly inferior in electrical and thermal conductivity. Typical grades include the 62 % and 65 % copper alloys H62 and H65 in the Chinese system, equivalent to C26000 and C26800 in UNS.

The standards follow the same split. Copper strip for general purposes is produced to ASTM B152/B152M in the American system and to EN 1652 in the European system, while brass strip is produced to ASTM B36/B36M and to the corresponding EN grades. GB/T 2059 covers copper and copper alloy strip for the Chinese market, so both families can be ordered under a single national strip standard where required.

Property Comparison

Property Copper strip Brass strip
Purity / main constituents Above 99.9 % copper 55 - 70 % copper, 30 - 45 % zinc
Electrical conductivity About 100 % IACS About 27 - 28 % IACS for 30 - 40 % zinc grades
Thermal conductivity Very high Markedly lower
Strength and hardness Moderate, increased by cold rolling Higher for the same temper, with better wear resistance
Machining and forming Excellent ductility, soft and easy to form Better machining behaviour and good formability in the soft tempers
Corrosion behaviour Stable, tarnishes to patina in moist air Good general corrosion resistance with a decorative yellow colour

Both materials are supplied in soft, half hard, hard and spring tempers with the corresponding strength and elongation ranges, and both are produced in thickness from about 0.05 mm upward with slit widths set to the customer's tooling.

Applications of Copper Strip

Conducting components for wires, motors, transformers and generators.

Circuit boards, busbar links and electronic device contacts.

Heat exchangers and radiators where thermal conductivity improves cooling efficiency.

Decorative art pieces, architectural trims, roofing and flashing details.

Earthing and shielding components that need conductivity and corrosion resistance together.

Applications of Brass Strip

Precision mechanical components such as gears, bearings and valves.

Door and window fittings, decorative strips, railings and architectural hardware.

Electrical connectors, terminals and switch parts where strength and moderate conductivity are enough.

Musical instruments and hardware where tone and appearance matter.

Shipbuilding, automotive and general manufacturing parts formed from coil.

Selection usually follows the function of the part. Where the strip must carry current or move heat, copper strip is used. Where the part must resist wear, hold a thread, take a bright decorative finish or be produced at high speed on a press or automatic machine, brass strip is the better choice, and its conductivity is usually adequate for the current levels involved. A common engineering compromise is to use brass strip for the structural body of a component and copper strip or a copper braid for the current path.

Strip is supplied slit to width, in coil or in cut lengths, with edges deburred and surfaces protected against oxidation, and with chemical composition and mechanical properties certified for each lot. Edge condition, camber, thickness tolerance and surface finish are controlled because they determine how the strip runs through high speed stamping and forming tooling.

Frequently Asked Questions

Q: What is the main difference between copper strip and brass strip?

A: Copper strip is more than 99.9 % pure copper and is chosen for conductivity, while brass strip is a copper-zinc alloy with 30 - 45 % zinc and is chosen for strength, wear resistance and machinability.

Q: How much lower is the conductivity of brass strip?

A: Brass strip with 30 - 40 % zinc conducts at about 27 - 28 % IACS, compared with about 100 % IACS for high purity copper strip. That is why brass is used for structural and decorative parts rather than for current carrying conductors.

Q: Which standards apply to each strip type?

A: Copper strip is produced to ASTM B152/B152M and EN 1652, brass strip to ASTM B36/B36M, and GB/T 2059 covers copper and copper alloy strip in the Chinese system.

Q: Can brass strip be substituted for copper strip to save cost?

A: Only where the electrical or thermal duty allows it. Brass strip works well for terminals and decorative parts, but any component whose function depends on high conductivity or heat transfer must stay with copper strip.

Q: What tempers are available?

A: Both materials are supplied in soft, half hard, hard and spring tempers, with strength and elongation ranges that follow the temper and the delivery thickness.

Q: What is controlled on a strip order?

A: Chemical composition, mechanical properties for the ordered temper, thickness and width tolerance, edge condition, camber, coil dimensions and surface finish, with certification for each lot.

goTop