Gnee Steel (Tianjin) Co., Ltd.

The process flow of recycled copper

Apr 10, 2024

The process flow of recycled copper

info-266-190Buy Wholesale China Preferential Supply High Quality Copper Rod/tu1 Tp2 T3  High Quality Copper Rod & Copper Bars/rods at USD 2880 | Global SourcesCopper Alloy Seamless Tubes for Heat Exchangers Tu0 Tu1 Tu2 - China Copper  Tube, Copper Pipe | Made-in-China.com

It mainly refers to the "waste" generated during the industrial production process. This kind of "waste" is mostly leftover materials and machining debris. If strictly managed, the grades of copper and alloys can be distinguished, and this resource can be recycled by corresponding copper processing plants. Taking copper and copper alloy processed materials as an example, about 30-40% of the consumed copper processed materials become scraps. In actual production, it is also called the utilization rate of copper processed materials. The scrap materials in various electrical component factories are times Popular because they are mostly pure copper semi-finished products produced by mechanical processing.

The second type of copper renewable resources is called old resources

It is a copper product among all kinds of industrial products, equipment, and spare parts. The source of this resource is very complex. The life cycles of various industrial products vary widely. Among them, recycled copper can only be obtained after dismantling industrial products, and it is often a variety of copper. Alloys are mixed together. For example, in automobile heat dissipation, the water tank tube is made of H90 brass, the heat sink is made of T2 corrugated strip, and they are welded together with lead-tin solder. The water tank water chamber is made of H68 alloy, etc. Important second-category renewable resources include: electronic components, car water tanks, air conditioners, scrap copper conductors (wires, cables, conductive copper bars), etc. According to data from the International Copper Association, the true recovery rate of copper put into use is 85%, and the rest will participate in the material cycle of nature.

There are many types of recycled copper resources, and the regeneration methods are also different, but the basic procedures are: inspection and acceptance of recycled copper raw materials - determination of impurity ratio - sampling and analysis of components - pre-processing of recycled materials - furnace smelting (reverberatory furnace, crucible Boilers, induction furnaces) - casting (castings, pressure processing billets, copper wire rods, thick copper blocks, remelted alloy ingots, etc.)

Examples of typical copper regeneration processes are as follows:

1. Purple copper (bare copper wire) - pretreatment (selection, drying, bundling, packing, briquetting, etc.) - reverberatory furnace smelting (20-100 tons/furnace) oxidation, reduction - intermediate holding furnace --Continuous casting and rolling copper bright rod (copper content ≥98.0%, conductivity ≥98%IACS);

2. Brass → Pretreatment (selection, bundling, packaging, bulk materials, etc.) → Induction melting (3-6 tons/furnace) → Holding furnace (6 tons) → Multi-line horizontal continuous casting billet → Lead brass Free cutting bar (HPB58-2, used for lock making)

3. Car and tractor water tanks → dismantle and remove the shell → bake and partially remove the lead and tin solder → melt and remove slag in the crucible boiler → iron mold casting → brass ingot → analyze chemical composition → for the production of cast brass parts, Bearings, valves, sanitary ware, etc.

4. Air conditioner evaporator and condenser → pretreatment (cut off elbows, end plates, remove oil, and crush to a length of 30-50 mm) → wind blowing to remove aluminum radiators → magnetic separation to remove iron → packaging → melting in the furnace Aluminum bronze, aluminum brass, and copper ingots can also be produced;

5. Recycled brass copper ingot → induction melting of high-strength and wear-resistant brass;

6. Cables are made into copper rice → used directly as ingredients for copper smelting. In order to prevent the copper powder from floating on the surface of the copper liquid, it can be packed with copper sheets and pressed into the copper liquid;

7. Copper shavings and brass shavings → briquetting → induction melting → obtaining remelted copper ingots → smelting corresponding alloys;

8. Copper oxide and copper ash → mix charcoal chips, clay, etc., make agglomerate → fire smelting copper, reduce blister copper → ingot → anode furnace → anode plate → electrolytic refining into electrolytic copper.

With the development of recycled copper industrialization and recycling technology, recycled copper production has developed in the direction of mechanization, continuity, and automation. Overseas developed countries have seen the globalization of important recycled copper varieties such as home appliances, electronic components, and heat exchangers. Recycling and production lines, with economic development, recycled copper will appear in the industrial system as an important industry.

goTop