Gnee Steel (Tianjin) Co., Ltd.

Copper, Brass and Bronze Strip Grades: Properties and Industrial Uses

Apr 15, 2024

What a Copper Strip Is and How It Is Supplied

A copper strip is a flat-rolled copper or copper alloy product delivered in coils rather than in flat sheets. The usual mill range covers strip from about 0.1 to 3 mm thick and 50 to 250 mm wide, while rolled material between roughly 0.06 mm and 1.5 mm thick is conventionally called strip by the trade. Heavy strip can reach approximately 2 mm in thickness and 600 mm in width. Because strip is coiled, orders are normally placed to a minimum length instead of a fixed length, and the coil is later slit, blanked or stamped into the final part.

Production follows a fixed sequence: melting and casting, hot rolling, cold rolling, intermediate annealing, finish rolling, edge trimming and degreasing. Temper control multiplies the value of a single alloy, because the same grade can be supplied soft, half-hard or hard, and each temper changes yield strength, elongation and bending behaviour without changing the chemistry.

Pure Copper Strip Grades: T2, T3, TP1, TP2, TU2 and TAg0.1

The wrought designations used in this section follow GB/T 5231, while dimensional and tolerance requirements for strip are covered by GB/T 2059. Pure copper grades are selected mainly for electrical conductivity, thermal conductivity and corrosion resistance.

T2 and T3 combine good electrical conductivity, thermal conductivity, corrosion resistance and processing performance, so they serve conductivity, heat-transfer and anti-corrosion duties. Compared with T1, they carry more impurities and a higher oxygen content, which lowers conductivity and thermal conductivity. In practice this limits them to general copper parts such as electrical switches, gaskets, nails and oil pipes.

TP1 and TP2 are deoxidised phosphorus coppers with good welding and cold-bending behaviour. They can be processed and used in reducing atmospheres and are supplied mainly as tubes, occasionally as rod, plate, strip or wire. Their dominant applications are conveying pipes, condenser tubes, evaporator tubes and heat exchangers.

TU2 is a high-purity oxygen-free copper with excellent electrical and thermal conductivity. It is used above all in electric vacuum instruments and in precision instruments and equipment.

TAg0.1 is a silver-bearing copper with good wear resistance, stable electrical contact behaviour and good corrosion resistance.

Brass Strip: Ordinary, Leaded, Tin, Aluminium, Manganese, Iron, Silicon and Nickel Brass

Brass strip is a copper-zinc family, and the zinc content together with small alloying additions decides strength, machinability and corrosion behaviour.

H96 has low strength with good thermal and electrical conductivity.

H90 behaves similarly to H96 with slightly higher strength; it accepts metal plating and is used for water supply and drainage pipes, bimetallic sheets, medals and artwork.

H85 offers higher strength and good plasticity with good weldability and corrosion resistance, suiting condensing and heat-dissipating pipes, serpentine tubes, siphons and cooling equipment parts.

H80 is stronger and more plastic than H85 with better corrosion resistance, used for thin-walled tubes, corrugated tubes, papermaking screens and building supplies.

H70 combines excellent plasticity with high strength, good machinability, welding behaviour and corrosion resistance for heat exchangers, papermaking pipes, machinery and electronic parts.

H68 and H68A are close to H70 but tend to season cracking during cold working, which suits complex cold-stamped and deep-drawn parts such as corrugated pipes.

H65 has good mechanical properties and accepts hot and cold processing, making it suitable for small hardware, household items and screws.

H63 and H62 provide good mechanical properties with high hot plasticity, machinability, weldability and corrosion resistance for deep-drawn and bent load-bearing parts such as pins, nuts, barometer springs, heat sinks and ring pieces.

HPb59-1 and HPb59 are the most widely used leaded brasses, with good mechanical properties and machinability and reliable hot and cold pressure working. They suit structural parts produced by cutting and stamping, such as gaskets and bushings. HPb63-3 offers excellent cutting and anti-friction performance for watch parts and automotive tractor components, HPb63-0.1 has slightly lower machinability and serves general structural parts, and HPb60-1 provides high strength for high-strength structural parts.

HSn70-1 combines high corrosion resistance with good mechanical properties for corrosion-resistant ship parts and components in contact with steam or oil. HSn60-1, known as naval brass, suits ship parts and other components exposed to seawater, while HSn90-1 has high corrosion resistance and anti-friction behaviour for bushings and similar parts.

HAL77-2 is strong and hard with good plasticity and seawater corrosion resistance, and is used for condenser tubes and other marine corrosion-resistant parts. HAL67-2.5 offers good wear and seawater corrosion resistance, and HAL60-1-1 gives high strength for structural parts such as gears and shafts, though it is sensitive to corrosion cracking. HAL66-6-3-2 combines high strength, hardness and wear resistance with lower plasticity for heavily loaded worms and nuts.

HMn57-3-1 is strong and hard with lower plasticity but better corrosion resistance than ordinary brass, while HMn58-2 provides good mechanical properties with low thermal conductivity and good corrosion resistance for important anti-corrosion parts and weak-current electrical components. HMn55-3-1 serves general corrosion-resistant structural parts.

HFe59-1-1 is strong and tough with good anti-friction and corrosion behaviour for parts working in corrosive conditions, and HFe58-1-1 gives high strength and hardness with good machinability for high-strength corrosion-resistant parts.

HSi80-3 has good mechanical properties, machinability and corrosion resistance with no tendency to corrosion cracking, and is used for ship parts, steam and water pipes and pipe fittings.

HNi65-5 behaves similarly to silicon brass with good machinability, easy welding and brazing and high corrosion resistance for ship parts and steam and water pipework.

Bronze Strip: Wear-Resistant and Spring Grades

QSn4-3 offers high wear resistance and elasticity with good diamagnetic behaviour for corrosion-resistant and wear-resistant parts, springs, elastic components and diamagnetic components of chemical equipment.

QSn4-4-2.5 combines high wear resistance with good machinability and weldability and is used mainly for bearing sleeves, bushings and discs running under friction.

QSn6.5-0.4 carries more phosphorus than QSn6.5-0.1 and therefore brings better fatigue resistance, elasticity and wear resistance; apart from springs and wear parts it is used above all for wear-resistant copper mesh in the paper industry.

QSn7-0.2 provides high strength and elasticity with good wear resistance, weldability and corrosion resistance for medium-load friction parts such as bearings, bushings and worm gears.

Grade-to-Application Selection Table

Family Typical grades Key property Typical application
Pure copper T2, T3, TP1, TP2, TU2, TAg0.1 Conductivity and heat transfer Busbars, switches, condenser and heat-exchanger tubes
Ordinary brass H96, H90, H85, H80, H70, H68, H65, H63, H62 Strength and plasticity balance Water pipes, heat exchangers, hardware, deep-drawn parts
Leaded brass HPb59-1, HPb59, HPb63-3, HPb60-1 Machinability Gaskets, bushings, watch and tractor parts
Tin brass HSn70-1, HSn60-1, HSn90-1 Seawater corrosion resistance Marine parts, steam and oil conduits
Aluminium brass HAL77-2, HAL67-2.5, HAL60-1-1, HAL66-6-3-2 Strength in seawater Condenser tubes, gears, shafts, worms
Manganese, iron, silicon and nickel brass HMn57-3-1, HMn58-2, HFe59-1-1, HSi80-3, HNi65-5 Corrosion resistance and strength Ship parts, pipework, electrical components
Tin bronze QSn4-3, QSn4-4-2.5, QSn6.5-0.4, QSn7-0.2 Wear resistance and elasticity Bushings, bearings, springs, papermaking mesh

Frequently Asked Questions

Q: What thickness range defines a copper strip?
Rolled copper between roughly 0.06 mm and 1.5 mm thick is called strip. Standard supply covers 0.1 to 3 mm thickness and 50 to 250 mm width, and heavy strip reaches about 2 mm by 600 mm.

Q: Which copper strip grade conducts electricity best?
TU2 and T2 sit at the top of the conductivity range. TU2 is oxygen-free and therefore preferred where vacuum tightness and stable conductivity matter, such as electric vacuum instruments.

Q: When should leaded brass replace ordinary brass?
Choose HPb59-1, HPb59 or HPb63-3 when high-speed cutting and a smooth machined finish dominate the part cost, for example gaskets, bushings and watch components.

Q: Which strip grades survive seawater?
HSn60-1, HSn70-1, HSn90-1, HAL77-2, HAL67-2.5, HSi80-3 and HNi65-5 all provide strong seawater corrosion resistance, with aluminium brass generally preferred for condenser tubes.

Q: Why does H68 tend to crack after forming?
H68 and H68A are prone to season cracking during cold working. Stress relief annealing straight after forming removes the residual stress and greatly reduces the risk.

Q: Is copper strip sold in fixed lengths?
No. Strip is supplied in coils to a minimum length rather than a fixed length, and downstream slitting or stamping sets the final part dimensions.

goTop