The K, L and M Family under ASTM B88
Type K, Type L and Type M are the three wall-thickness classes defined for copper water tube in ASTM B88. They are not different alloys: all three are made from the same deoxidised copper, typically Cu-DHP (CW024A, UNS C12200), and they differ in wall thickness for a given outside diameter. Type K has the heaviest wall, Type L a medium wall and Type M the lightest wall of the three.
Because the outside diameter is held constant within a size, the heavier the wall, the smaller the bore and the higher the working pressure. That single relationship explains almost every selection decision between the classes, and it is why the wall thickness - not the nominal size - should be stated on an order.
| Class | Relative wall | Typical application |
|---|---|---|
| Type K | heaviest of the three | buried and underground runs, service mains, high-pressure duty |
| Type L | medium wall | interior plumbing, heating, refrigeration and HVAC lines |
| Type M | lightest wall | low-pressure drainage, heating and non-critical interior work |
Wall Thickness, Pressure and Flow
Working pressure rises with wall thickness while internal volume falls, so the three classes trade pressure containment against flow capacity at the same nominal size. In practice, designers specify the class that satisfies the pressure and mechanical protection requirement at the lowest material cost, then confirm that the reduced bore still delivers the required flow at the available pump head.
Copper water tube is supplied in drawn temper, which is straight in length and strong, and in annealed temper, which is soft and supplied in coils for bending around obstacles without fittings. The temper must be stated alongside the class, because an annealed Type L coil and a hard drawn Type L length behave quite differently on site.
Where Type K and Type L Are Used
Type K is chosen where the tube cannot be inspected after installation or where mechanical damage is likely: buried service lines, underground supply mains, and connections through foundations or slabs. The extra wall gives a corrosion allowance and resistance to point loading that the lighter classes cannot match.
Type L is the general-purpose plumbing and HVAC class. It carries domestic hot and cold water, heating circuits and refrigeration lines, and it bends and flares well in the annealed condition. In refrigeration and air conditioning work, copper tube is more often specified to ASTM B280 or the EN 12735 series, because those standards add cleanliness, dryness and capping requirements that general water tube standards do not impose.
How ACR Tube to ASTM B280 Differs
Air conditioning and refrigeration tube is a different specification even when the outside diameter matches. ASTM B280 requires the tube to be supplied cleaned and dried, with residual contamination controlled and the ends capped so that moisture and dust cannot enter before brazing. Tube supplied to a general water tube standard may meet the dimensional requirement and still fail the cleanliness requirement of a refrigeration circuit.
European refrigeration and air conditioning work uses the EN 12735 series for the same reason, while EN 1057 covers copper tubes for water and gas in sanitary and heating applications. Matching the standard to the duty - water, gas or refrigerant - is more important than matching the diameter.
Choosing the Right Tube for the Job
Start from the service condition: fluid, pressure, temperature, whether the tube will be buried or exposed, and whether it must be bent or joined. Then confirm the class, temper, dimensions and standard, and check that the fittings, brazing alloy and support spacing are compatible with the wall thickness selected. Fittings rated for one class may not have adequate engagement depth on another, so the tube and fitting schedules should be reviewed together rather than separately.
Frequently Asked Questions
Q: Is Type K stronger than Type L copper pipe?
A: Yes. Type K has a heavier wall than Type L at the same outside diameter, so it carries a higher working pressure and tolerates more mechanical damage, at the cost of a smaller bore and higher material content.
Q: Which type is used for buried water lines?
A: Type K is the usual choice for buried and underground service lines, because the heavier wall provides a corrosion and damage allowance where the tube cannot be inspected later.
Q: Can Type L tube be used for air conditioning lines?
A: It can be dimensionally similar, but refrigeration circuits should use tube specified to ASTM B280 or EN 12735, since those standards add the internal cleanliness, dryness and capping requirements that a charged system needs.
Q: Does a larger nominal size always mean a larger bore?
A: No. Outside diameter is held within a size, so a heavier wall gives a smaller bore. The wall thickness and class must be stated to know the true internal diameter.
Q: Is copper water tube available in coils as well as straight lengths?
A: Yes. The soft annealed condition is supplied in coils for bending without fittings, and the hard drawn condition is supplied straight for rigid runs.







