Gnee Steel (Tianjin) Co., Ltd.

Cupronickel Raw Materials, Melting Formulas and Processing

Apr 12, 2024

What White Copper Really Is

White copper, or cupronickel, is a copper alloy in which nickel is the principal added element. A binary copper-nickel alloy is called simple cupronickel, and grades that also contain iron, manganese or zinc are complex cupronickel. The metal has a silvery white appearance, good resistance to seawater and to stress corrosion, and a stable electrical resistance, which is why it is made into tube, rod, plate, strip, foil and wire rather than sold as an ingot only.

The common misconception to clear up first is that white copper is not a brass. Brass is copper plus zinc; cupronickel is copper plus nickel, and its zinc content is low or absent. Mixing the two families in one charge is one of the fastest ways to lose a heat, because zinc raises vapour pressure in the melt and changes both the corrosion behaviour and the colour of the finished product.

Raw Materials and Charge Composition

Charge material Function in the melt
Electrolytic cathode copper base metal; purity to GB/T 467 cathode grades keeps residuals low
Nickel, or copper-nickel master alloy main alloying element; added as master alloy to control melting point and solution time
Iron and copper-iron master alloy improves resistance to seawater impingement and grain structure
Manganese deoxidation, desulphurisation and property control
Return scrap, first grade clean, identified in-house returns of the same grade
Purchased scrap only with verified composition; sorted by grade to avoid cross contamination

The wrought cupronickel designations and their chemical composition are fixed by GB/T 5231 for the Chinese market, with the 10% nickel grade and the 30% nickel grade as the two volumes that dominate tube and plate production. Product standards then govern dimensions and mechanical properties: GB/T 1527 and EN 12449 for tube, ASTM B111 and ASTM B466 for condenser and piping tube, and ASTM B122 for plate, sheet and strip.

Batching Rules That Keep a Heat Inside Specification

Set the charge so that the selected raw material grade is equal to or slightly better than the finished product grade; never dilute a specification with lower grade stock.

For expensive elements such as nickel, aim at the middle to lower half of the standard range, because top-of-range additions cost money without adding service value.

Allow for element loss during melting. Nickel and copper are stable, but manganese and zinc are not, so the charge is calculated with an allowance for oxidation, volatilisation and dross loss.

Make up refractory, volatile or easily oxidised constituents as master alloys before the final melt; nickel, iron and manganese are added in this way rather than as pure metals.

Match new metal with returns deliberately: primary returns, secondary returns and small or large sized scrap are proportioned so that the melt stays consistent from heat to heat.

Batch complex alloys heat by heat and weigh every constituent, including the master alloys. Trial-and-error charging shows up later as variation in tube wall thickness and conductivity.

Melting, Casting and Processing Route

The melt is protected with a dry charcoal or flux cover because both copper and nickel oxidise, and nickel oxide is very difficult to reduce once it is in the bath. Deoxidation is carried out with manganese or a controlled magnesium addition, never with phosphorus, since residual phosphorus harms weldability and the alloy's performance in seawater. Pouring temperature is set a moderate amount above the liquidus of the grade; excessive superheat increases gas pickup and grain coarsening, while too little superheat causes misruns in thin-walled tube blanks.

After casting, the processing route to finished product is conventional for copper alloys: hot working of the cast slab or billet, annealing, cold rolling or cold drawing with intermediate anneals, and a final anneal or temper roll that fixes the mechanical properties and grain size. Tube for heat exchangers is finished in the annealed temper for bending, then eddy-current tested over its full length and pressure tested before packing. Strip and plate are annealed to the specified temper and inspected for surface defects, since cupronickel is unforgiving about inclusions and rolled-in oxide that later become leak paths.

Quality Control and Common Defects

The defects that most often cost a cupronickel producer a lot are gas porosity, oxide inclusions, and chemistry drift in manganese and iron. All three are controlled at the melt stage, so the working practice is built around melt protection, verified charge weights, and a spectrographic analysis taken before pouring rather than after casting. A heat that is out of range on nickel or iron cannot be corrected after solidification at acceptable cost.

Release testing for a cupronickel order usually combines a chemical analysis from the heat, tensile testing in the specified temper, grain size determination, eddy-current examination and a pressure test for tube, flaring or flattening tests where the product standard requires them, and dimensional inspection. Certificates are issued to EN 10204 type 3.1 with a heat number that follows the material through to the finished bundle, which allows a failed part to be traced back to a specific cast and melt.

Frequently Asked Questions

Q: Is white copper the same as brass?

A: No. White copper is a copper-nickel alloy, where nickel is the main added element; brass is a copper-zinc alloy. The two families have different colour, corrosion behaviour and melting practice, and their charges must be kept separate.

Q: Which standard fixes cupronickel composition?

A: GB/T 5231 sets the designations and chemical composition of wrought copper and copper alloy grades, while product standards such as GB/T 1527, ASTM B111, ASTM B466 and ASTM B122 set dimensions, temper and mechanical requirements for tube, pipe, plate and strip.

Q: Why is phosphorus not used for deoxidation in cupronickel?

A: Residual phosphorus damages weldability and seawater performance. Manganese or a controlled magnesium addition is used instead, together with a protective cover that limits oxygen pickup in the first place.

Q: What is the biggest risk when buying cupronickel scrap for remelting?

A: Cross contamination with brass or bronze. Zinc and lead enter the melt and cannot be removed at reasonable cost, so purchased scrap must be sorted by grade and verified by analysis before it is charged.

Q: How is cupronickel tube delivered for heat exchanger service?

A: In the annealed temper for bending and rolling into tube plates, with full-length eddy-current examination, a hydrostatic or pneumatic pressure test, dimensional records and often as U-bent bundles with heat numbers marked per bundle.

Q: Can cupronickel be welded and fabricated on site?

A: Yes, with matching filler metal and controlled heat input, but the joint area should stay clean and the fit-up tight. Residual phosphorus and sulphur in the base metal are the main reasons a weld can fail in seawater service.

goTop