Grade Definition and Standard Position
CC493K is the European designation for the leaded tin bronze CuSn7ZnPb, a casting grade listed in EN 1982, the standard for copper and copper alloy castings. In North America the same alloy family is known as C93200 and is covered by ASTM B505 for continuous castings and by ASTM B584 for sand castings; the older German designation is RG7 under DIN 1705. It is tin bronze with zinc and lead additions, often called red bronze or leaded bronze in trade use, and it is the most widely consumed bearing bronze on the market.
The name tells the story: tin provides strength and load capacity, lead provides the lubricity and chip-breaking that make the alloy easy to machine, and zinc improves castability and economics while keeping the alloy single phase and sound. The result is a semi-rigid material with a good combination of wear resistance, corrosion resistance and elongation.
Chemical Composition
| Element | Content, % |
|---|---|
| Cu | 81.0 to 85.0 |
| Sn | 6.0 to 8.0 |
| Pb | 5.0 to 8.0 |
| Zn | 2.0 to 5.0 |
| Ni | 2.0 max |
| P | 0.10 max |
| Al | 0.01 max |
| Fe | 0.2 max |
| S | 0.10 max |
| Sb | 0.3 max |
| Si | 0.01 max |
Two notes belong with that table. Copper content includes nickel, so a nickel-bearing charge is accounted for in the copper figure. For continuous castings and centrifugal castings the minimum tin content is set lower, at 5.2%, because the faster cooling of those processes produces a finer structure that reaches the required properties with slightly less tin; for ingots the maximum copper content is 86.0%.
Mechanical and Physical Properties
| Property | Value |
|---|---|
| Tensile strength, Rm | 260 MPa |
| 0.2% proof strength, Rp0.2 | 120 MPa |
| Elongation, A5 | 12% |
| Brinell hardness | 70 HBW |
| Density | 8.8 kg/dm3 |
| Specific heat | 0.356 J/(g*K) |
| Thermal expansion | 18.5 x 10-6 per K |
| Thermal conductivity | 64 W/(m*K) |
| Electrical conductivity | about 7.5 MS/m |
The relatively low hardness combined with 12% elongation is exactly what a bearing material needs: the bronze conforms slightly to the shaft, embeds foreign particles instead of scoring the journal, and carries the load without becoming brittle. Where higher strength is required at the same wear surface, casters move to a high-tensile manganese aluminium brass such as the CuZn25Al5Mn4Fe3-C grade.
Bearing Performance and Applications
Bushings, sleeve bearings and thrust washers for pumps, electric motors, conveyors and general machinery.
Worm wheel blanks and gear components at moderate load, where machinability and quiet running matter.
Pump bodies, impellers and wearing rings for industrial water service.
Valve bodies, glands and stems in general industrial and marine fittings.
Bearing cages, slide blocks and guide bushes machined from continuous cast bar.
Design practice for these bearings sets a running clearance based on shaft diameter and a maximum load per projected area that keeps the oil film intact; the alloy tolerates short periods of boundary lubrication but not sustained dry running, and lubrication grooves should be positioned to feed the loaded zone. Where the shaft is stainless steel and the environment is wet, the galvanic couple and the risk of crevice corrosion at the bearing housing should be reviewed before the grade is fixed.
Casting, Machining and Quality Control
The alloy is cast by sand casting, permanent mould casting, centrifugal casting and continuous casting. Continuous and centrifugal casting give the densest structure and are the standard supply route for bar, tube and bushings, while sand casting suits larger and more complex bodies. Melting practice is straightforward but requires clean charge material and adequate deoxidation, because porosity and lead segregation are the two defects that most affect bearing performance. Lead is essentially insoluble in copper and forms discrete particles, so the solidification rate controls their size and distribution.
Machining is one of the alloy's strengths: free-cutting behaviour gives short chips, good surface finish and long tool life at moderate cutting speeds, making it economical for high-volume bushing production. Welding is not normally used; components are joined by pressing, keying or brazing.
Release inspection for export orders typically covers a heat analysis against the table above, tensile test from a separately cast test bar, hardness measurement, dimensional inspection and, for pressure-retaining castings, a leak test or non-destructive examination. Inspection documents are issued to EN 10204 type 3.1 with a heat number marked on each casting so that the lot remains traceable through machining and assembly. Because the alloy contains lead, it is not suitable for potable water components or for applications where lead release is regulated, and that restriction should be confirmed at the enquiry stage rather than after delivery.
Frequently Asked Questions
Q: Which alloys correspond to CC493K?
A: CC493K is the EN 1982 designation for CuSn7ZnPb. The equivalent North American family is C93200, covered by ASTM B505 for continuous castings and ASTM B584 for sand castings, and the older German standard DIN 1705 designates it RG7.
Q: What are the typical mechanical properties?
A: Tensile strength of about 260 MPa, 0.2% proof strength of about 120 MPa, elongation of about 12% and Brinell hardness near 70 HBW, with a density of 8.8 kg per cubic decimetre.
Q: Why is lead added to tin bronze?
A: Lead is practically insoluble in copper and forms discrete particles that act as a solid lubricant and break the chip during machining. That gives the alloy its excellent machinability and its ability to run against a steel shaft under boundary lubrication.
Q: Can CC493K be used for potable water fittings?
A: Not normally. Lead content of 5 to 8% rules it out where lead release is regulated, such as drinking water components. A lead-free or low-lead bronze should be selected for those applications.
Q: Which casting process is best for bearing bushes?
A: Continuous casting or centrifugal casting, because the faster solidification produces a denser structure with finer lead distribution, which improves load capacity and surface finish after machining.
Q: How are castings verified before shipment?
A: By heat analysis against the composition limits, tensile testing of a separately cast bar, hardness measurement, dimensional inspection against the drawing and, where required, a leak test or non-destructive examination, with certificates to EN 10204 type 3.1.







