Gnee Steel (Tianjin) Co., Ltd.

H68 Brass Properties

Feb 05, 2026

What is H68 brass?

H68 brass is an α single-phase copper-zinc alloy (with a zinc content of approximately 32%) within the Chinese national standard system. It belongs to the category of high-quality ordinary brass. Due to its balanced plasticity, machinability, and corrosion resistance, it is one of the most widely used brass varieties in industry. The following is its structured detailed information.

Get H68 Brass Spec Sheet

Core Chemical Composition (GB/T 5231-2022 Standard)

Element Content Range (mass fraction) Description
Copper (Cu) 67.0% – 69.0% Core element, determines fundamental alloy properties.
Zinc (Zn) Balance (~31% – 33%) Main alloying element, adjusts strength.
Impurity (Pb) ≤ 0.03% Environmental grade requirement; some standards may permit ≤0.07%.
Impurity (Fe) ≤ 0.10% Controlled to avoid affecting machinability.
Impurity (Sn) ≤ 0.05% Prevents embrittlement, ensures plasticity.
Total Impurities ≤ 0.30% Strictly controlled to stabilize performance.

 

Key Performance Parameters

Physical Properties:

Density: 8.50 – 8.55 g/cm³ (at 20°C)

Melting Point: 930 – 960°C (varies slightly with zinc content)

Electrical Conductivity: 25% – 30% IACS (room temperature)

Thermal Conductivity: 115 – 125 W/(m·K) (room temperature)

Coefficient of Thermal Expansion (20-200°C): 19.5 × 10⁻⁶/°C

Modulus of Elasticity: ~110 GPa (annealed state)

 

Mechanical Properties (Varies with processing condition):

Processing Condition Tensile Strength (MPa) Yield Strength (MPa) Elongation (%) Vickers Hardness (HV)
Annealed (M) 280 – 350 ≥ 120 ≥ 55 60 – 100
Half-Hard (Y2) 380 – 480 ≥ 200 ≥ 25 90 – 140
Hard (Y) 500 – 600 ≥ 350 ≥ 10 130 – 180

 

Corrosion Resistance & Machining Performance:

Corrosion Resistance: Good in atmosphere, fresh water, and neutral salt solutions. Shows some tolerance to weak organic acids (e.g., acetic, citric), but is prone to stress corrosion cracking (SCC) in environments containing ammonia, hydrogen sulfide, and strong acids (e.g., hydrochloric, nitric). Long-term contact should be avoided, or passivation treatment applied.

 

Machining Performance:

Cold Working: Excellent plasticity; suitable for complex forming like deep drawing, stretching, bending, cold heading. Cold deformation rate between anneals can exceed 85%, ideal for thin-walled, special-shaped parts.

Hot Working: Hot working temperature 750 – 850°C; can be forged, hot-rolled, extruded. Post-processing annealing is required to relieve stress.

Machinability: Medium (machinability rating ~70%); requires dedicated cutting fluids; suitable for turning and milling precision parts.

Weldability: Suitable for soft soldering, brazing, TIG welding; gas shielded welding results are average. Post-weld annealing is recommended.

H68 brass for electrical connectors
H68 brass alloy composition
H68 brass sheet supplier
High precision H68 brass strip manufacturer

Inquire about H68 Brass Pricing & Samples

 

Implementing Standards and Corresponding International Grades

Chinese Standards: GB/T 5231-2022 (Brass Chemical Composition), GB/T 2059-2000 (Brass Strip/Plate), GB/T 1527-2017 (Brass Tube), GB/T 4423-2017 (Brass Rod). Components in contact with drinking water must comply with GB/T 17219-1998 health requirements.

 

International Equivalent Grades:

Standard System Equivalent Grade Notes
U.S. Standard C26200 (CDA262) Slightly higher zinc content (31%–34%), similar performance.
European Standard CW506L (CuZn33) High compositional match, generally interchangeable.
British Standard CZ108 Slight differences in impurity control ranges.
Japanese Standard C2680 Equivalent to H68, widely used.
German Standard 2.0280 Contains 32% zinc, identical performance.

 

Product Forms and Typical Applications

Product Forms:

Plate/Strip: Thickness 0.05 – 50 mm (strips often for electronic components, plates for structural parts).

Rod: Diameter 3 – 500 mm (round, square; suitable for cold heading, machining).

Tube: Outer Diameter 6 – 219 mm (seamless, welded; used for fluid transport).

Wire: Diameter 0.1 – 20 mm (used for weaving, rivets, springs).

 

Core Application Areas:

Electronics/Electrical: Connector terminals, relay contact springs, lead frames, switch contacts (utilizes high conductivity + easy forming).

Precision Machinery: Watch/clock parts, instrument housings, valve cores, hydraulic bellows (relies on high plasticity + dimensional stability).

Architecture/Decoration: Plumbing fittings, door handles, decorative trim, lamp housings (balances aesthetics + atmospheric corrosion resistance).

Automotive: Radiator fins, fuel line connectors, electrical connectors (suits cold working + heat dissipation needs).

Other: Musical instrument parts (e.g., saxophone body), zipper teeth, eyeglass frames, drinking water pipe fittings (meets environmental requirements).

 

Differences from Similar Grades (H62, H70, C26000)

Grade Key Difference Typical Application Focus
H68 32% Zn, optimal plasticity, good corrosion resistance. Complex forming, precision parts, deep-drawn components.
H62 38% Zn, higher strength, slightly lower plasticity. Structural parts, fasteners, cost-effective hardware.
H70 30% Zn, slightly higher conductivity, similar plasticity. Electronic terminals, heat sinks, decorative parts.
C26000 U.S. equivalent to H70, 30% Zn, stricter impurity control. Export products, high-precision parts with demanding requirements.

 

Get Dedicated Engineer Support

Our factory

Our factory is equipped with an advanced full-process copper processing production line, specializing in the manufacturing of high-precision copper plates, copper tubes, copper rods, copper wires, and copper strips. The core of our production includes continuous casting and rolling units, precision extrusion lines, high-speed cold rolling equipment, multi-roll precision rolling mills, tube drawing systems, and intelligent stretching production lines. We are also outfitted with comprehensive inspection equipment such as spectrometers and online eddy current flaw detectors, ensuring full-process control from smelting and casting, hot processing, to cold finishing. Our products achieve an accuracy of up to ±0.01mm, with an annual production capacity exceeding 50,000 tons. They are widely used in power, electronics, transportation, and high-end manufacturing sectors. Certified with international standards such as ISO9001 and IATF16949, we are capable of providing global customers with one-stop copper material solutions.

H68 brass rod stock wholesale

 

Brass product packaging

We implement a graded and customized packaging system: copper plates are double-wrapped with moisture-proof paper and vapor corrosion inhibitor film before being placed in reinforced wooden crates, which are filled with cushioning materials and equipped with impact-resistant corner protectors; copper tubes and rods are sealed with plastic end caps, wrapped with PE protective film, and then layered into steel-frame logistics containers, with EPE pearl cotton separating each layer; copper wires are automatically wound onto spools, vacuum-sealed, covered with waterproof film, and secured on customized iron-wood pallets; copper strips are wrapped with non-woven fabric, coiled onto high-strength steel cores, and placed into waterproof composite material coils with desiccants inside. All packaging passes ISTA-3A transport testing, and the outer boxes are labeled with international hazardous material identifiers, moisture warnings, and scannable logistics codes, ensuring the cargo withstands moisture, impact, and chemical erosion during global transportation.

H68 brass tube for heat exchanger

Get Fast Quote & Logistics Plan

 

goTop