Why Titanium Alloy Forgings Crack So Readily
Titanium alloys combine low density, high specific strength, good elevated-temperature stability, corrosion resistance, non-magnetic behaviour and biocompatibility, which is why forged bars, step shafts, discs and rolled profiles are used throughout aerospace, chemical and petroleum equipment, medical devices and nuclear plant. Forging deformation is the primary means of converting a cast ingot into a sound, uniform microstructure. The difficulty is that titanium has low thermal conductivity, strong sensitivity to temperature and, in several alloy families, limited deformability, so ingot-to-bar operations regularly produce cracks of several distinct types. Every crack adds grinding labour, lowers yield and, in the worst cases, scraps an entire billet.
The Seven Types of Titanium Forging Cracking
Production records from titanium billet conversion group forging cracks into seven recurring modes. They differ in location, direction and origin, so each must be diagnosed on its own before a remedy is chosen.
| Type | Where it appears | Typical cause |
|---|---|---|
| End face cracking | Upset billet ends; large, open cracks | Pipe or cold segregation not cleaned from ingot ends; cold anvil contact; uneven end deformation; high-resistance, low-fluidity material |
| Folding cracking | Mid-length folds, often after grinding pits | Ingot height-to-diameter ratio above 2.5; residual sampling grooves; sharp machining or sawing edges left unpolished |
| Tearing | Transverse, localised, along the drawn length | Single-pass reduction too heavy or too fast; worn or inadequately preheated anvil edges; step sections and abrupt size changes |
| Internal cracking | Inside the billet, invisible to the eye | Segregation, inclusions, porosity or cold shuts in the ingot; rapid cooling of small-diameter bar; sharp local temperature gradients |
| Longitudinal cracking | Along the flow direction at chamfers and corners | Corner cooling ahead of the bulk section; water or oil quenching of temperature-sensitive high-temperature alloys |
| Brittle cracking | Deep, difficult-to-remove cracks in hard-to-deform alloys | Forging below the final forging temperature; no low-temperature furnace stage; heating too fast for the alloy conductivity |
| Surface cracking through the body | Extensive surface cracks across a whole billet | Poor ingot metallurgical quality; cold segregation and subsurface porosity not removed; opening temperature set too low |
Metallurgical, Thermal and Process Causes
Metallurgical origin: segregation, inclusions, shrinkage porosity, cold shuts and subsurface blowholes left from melting and casting become crack initiation sites and can persist through several forging heats.
Thermal origin: titanium conducts heat poorly, so rapid heating or rapid cooling creates a large gradient between surface and core and between end and centre. The resulting thermal stress exceeds the local ductility and starts cracks.
Process origin: excessive pass reduction, high deformation rate, cold anvils, worn anvil edges, unpolished machining edges and uncontrolled transfer times all fall into the shop-floor process category.
Material origin: near-alpha and ordered intermetallic titanium alloys such as Ti3Al and Ti2AlNb, and hard-to-deform high-temperature grades, have intrinsically low deformation capability, so their window of safe processing parameters is narrow.
Prevention Measures for Each Cracking Mode
End face cracking: confirm by ultrasonic inspection that pipe and cold segregation are fully removed from ingot ends; preheat the anvil to at least 300 C; wrap both upset ends in insulating blankets to cut heat loss to the anvil; forbid excessive deformation rate and uneven deformation during drawing out; use a curved upsetting plate for material with high resistance and low fluidity so metal flows from the centre outwards.
Folding cracking: keep the height-to-diameter ratio below 2.5, with 1.8 to 2.3 preferred; machine or grind residual sampling grooves and prior fold damage to a smooth blend; remove all sharp edges left by sawing, machining and positioning holes before the next forging step.
Tearing: hold single-pass unilateral reduction to 20 to 30 mm and reduction rate to about 5 to 10 mm/s; maintain anvil edge curvature of R40 mm or greater and preheat anvils to 300 to 400 C; for stepped shafts use light knocking passes followed by gradual multi-hammer reduction limited to 30 mm per blow.
Internal cracking: attack the source by tightening melting practice for alloys containing refractory additions such as tungsten, molybdenum and niobium so that segregation and inclusions are reduced; chamfer small-diameter billet promptly during drawing; return material to the furnace rather than holding it cold.
Longitudinal cracking: chamfer during drawing and forbid sharp or black edges; for temperature-sensitive high-temperature alloys use air cooling or insulating blankets instead of water, oil or forced-air quenching.
Brittle cracking: apply wrapped-blanket forging, meaning heat to the specified soak, withdraw the billet, wrap about 10 mm of insulation with a glass protective agent, return it to the furnace, then forge with the blanket kept in place so the billet never falls below the final forging temperature; heat through a 200 to 300 C low-temperature furnace stage with multi-stage, slow ramps of 50 to 100 C per hour.
Surface cracking through the body: improve melting quality, remove cold segregation and subsurface porosity before forging, and set the opening forging temperature above the beta transus with a clear margin instead of close to it.
Process Control Parameters That Matter
| Parameter | Recommended value | Purpose |
|---|---|---|
| Anvil preheat temperature | At least 300 C; 300 to 400 C for drawing out | Reduce heat extraction from the billet surface |
| Anvil edge radius | R40 mm or more | Lower stress concentration and avoid tearing |
| Single-pass unilateral reduction | 20 to 30 mm | Limit shear strain per pass |
| Reduction rate | About 5 to 10 mm/s | Allow temperature and strain to redistribute |
| Ingot height-to-diameter ratio | 2.5 maximum, 1.8 to 2.3 preferred | Prevent upset folding |
| Grinding width-to-depth ratio | 10 or greater | Blend repairs without leaving a stress raiser |
| Heating rate for hard-to-deform grades | 50 to 100 C per hour after a 200 to 300 C stage | Limit thermal gradient |
| Insulation wrap thickness | About 10 mm with glass protective agent | Hold forging temperature above the final forging limit |
| Opening forging temperature | Above the beta transus with adequate margin | Avoid cracking in the as-cast structure |
The last row is the most expensive lesson in the table. A test ingot with a measured beta transus of 1020 C was opened at only 1050 C and cracked severely across the body; the same material reopened after reheating to 1150 C showed a dramatic reduction in cracking. Where the process window is narrow, the opening temperature must be set from measured transformation data rather than from an assumed value.
Inspection, Grinding and Repair
Titanium cracks are difficult to inspect and slow to repair, so the inspection plan must be written at the same time as the forging route.
Detection: visual inspection of every billet, low-magnification examination and ultrasonic testing for internal defects; dye penetrant inspection of finished forgings and of any grinding repair before release.
Blending limits: grind to a smooth blend with a width-to-depth ratio of at least 10, since a narrow deep groove simply re-initiates a crack at the next heat.
Grinding risk: local heating from grinding creates the very temperature gradient that keeps a crack propagating, so coolant and light passes are essential on thin or small sections.
Re-inspection: after blending, re-run penetrant or ultrasonic inspection to confirm complete removal; record the repair on the route card so that subsequent heats account for the reduced section.
Frequently Asked Questions
Q: What is the most common titanium forging crack?
End face cracking during upsetting is the most frequent and the most disruptive, because it often stops the process route. Dirty ingot ends, cold anvils and uneven end deformation are the leading causes.
Q: Why does brittle cracking dominate in high-temperature titanium alloys?
These alloys have limited plasticity, and titanium conducts heat poorly. Fast heating or forging below the final forging temperature produces steep gradients and brittle fracture that is deep and hard to grind out.
Q: What anvil preheat temperature should be used?
Preheat the anvil to at least 300 C, and keep it between 300 C and 400 C for drawing-out operations; cold tooling is a direct cause of end face cracking and tearing.
Q: How deep may a crack be ground?
Grind to a smooth-bottomed blend with a width-to-depth ratio of 10 or more. Never leave a narrow groove, because the next forging pass will open it again.
Q: Can internal cracks be found before the forging is finished?
They are usually hidden. Ultrasonic testing, low-magnification examination and, for small-diameter bar, inspection at the billet stage are used, but most internal cracks are only confirmed at final inspection, which is why preventing segregation at melting is decisive.
Q: Which parameters most influence cracking of high-temperature alloys?
Heating rate, furnace staging, opening temperature relative to the beta transus, and the insulation applied between furnace and anvil control the outcome far more than hammer capacity does.







