Chemical Composition and Fundamental Properties
H68 brass has a copper content of approximately 68% and a zinc content of about 32%. This specific ratio allows the material to maintain relatively high strength while possessing excellent plasticity and machinability. Its density is roughly 8.5 g/cm³, and the melting point ranges between 900-940°C. The exact values may vary slightly depending on processing methods and purity.
Technical Characteristics and Advantages
Mechanical Properties: The tensile strength of H68 brass can reach 370-420 MPa, with a yield strength of approximately 180-220 MPa and an elongation exceeding 40%. This combination of properties allows it to withstand certain loads while remaining easy to cold form (e.g., stamping, bending, drawing). For instance, its high elongation prevents cracking during the manufacturing of heat sink fins, while its moderate strength ensures structural stability.
Corrosion Resistance: The addition of zinc leads to the formation of a dense zinc oxide protective film on the surface of H68 brass. This film provides good corrosion resistance in dry air, fresh water, and neutral salt solutions. However, in humid environments or media containing ammonia, additional surface treatments such as tin or nickel plating are recommended to enhance protection.
Electrical and Thermal Conductivity: Its electrical conductivity is about 27% IACS (International Annealed Copper Standard), and its thermal conductivity is approximately 116 W/(m·K). While lower than pure copper, these values are sufficient for applications in power electronics, heat exchange equipment, and similar fields. For example, in motor terminals, H68 brass can balance both electrical conductivity and mechanical strength.
Machining Adaptability: H68 brass exhibits good hot and cold working performance. It can be formed through processes such as forging, rolling, and extrusion, and offers excellent weldability (suitable for gas welding, resistance welding, and brazing), making it ideal for manufacturing complex structural components.




Electronics and Electrical Appliances: Used in the manufacturing of connectors, terminals, switch components, etc. Its conductivity and corrosion resistance ensure long-term stability. Examples include mobile phone SIM card trays and computer heat dissipation modules, which often utilize H68 brass.
Architectural Decoration Industry: Valued for its golden color and ease of polishing, H68 brass is widely used for door handles, locks, decorative strips, etc. Its surface can be chrome or nickel plated to enhance aesthetics.
Mechanical Manufacturing: H68 brass is a cost-effective choice for applications requiring moderate strength and corrosion resistance, such as valves, pipe fittings, and gears. For example, connectors for water supply pipes commonly use this material.
Musical Instrument Manufacturing: Components of some brass instruments (e.g., trumpets, trombones) utilize H68 brass because its vibration characteristics are close to those of pure copper, yet it is more cost-effective.
Industry Standards and Important Notes
International Standards: H68 corresponds to C26800 in the U.S. ASTM B16M standard, CW508L in the European EN standard, and is clearly specified in China's national standard GB/T 5231-2012 for its composition and performance requirements.
Processing Parameters: During cold working, deformation is recommended to be controlled within 30%; otherwise, intermediate annealing (650-700°C for 1 hour) is required. The hot working temperature range is 750-850°C, avoiding overheating which can lead to coarse grain structure.
Environmental Requirements: H68 brass does not contain harmful elements such as lead or cadmium, complying with RoHS and REACH regulations. It can be used for food-contact components (e.g., the inner core of kitchen faucets).
Alternative Material Comparison
H59 Brass: Has a higher zinc content (approximately 41%), resulting in higher strength but reduced plasticity. It is suitable for manufacturing load-bearing components such as bolts and nuts, but its cold-working performance is inferior to that of H68.
H62 Brass: Has a copper content of 62% and lower cost, but its corrosion resistance and weldability are slightly inferior. It is often used in piping systems where performance requirements are not as stringent.
Copper (T2): Offers superior electrical and thermal conductivity but has lower strength and higher cost. It is used only for high-end electronic components or conductive busbars.
Get Dedicated Engineer Support
Our factory
Our factory is equipped with an advanced full-process copper processing production line, specializing in the manufacturing of high-precision copper plates, copper tubes, copper rods, copper wires, and copper strips. The core of our production includes continuous casting and rolling units, precision extrusion lines, high-speed cold rolling equipment, multi-roll precision rolling mills, tube drawing systems, and intelligent stretching production lines. We are also outfitted with comprehensive inspection equipment such as spectrometers and online eddy current flaw detectors, ensuring full-process control from smelting and casting, hot processing, to cold finishing. Our products achieve an accuracy of up to ±0.01mm, with an annual production capacity exceeding 50,000 tons. They are widely used in power, electronics, transportation, and high-end manufacturing sectors. Certified with international standards such as ISO9001 and IATF16949, we are capable of providing global customers with one-stop copper material solutions.

Brass product packaging
We implement a graded and customized packaging system: copper plates are double-wrapped with moisture-proof paper and vapor corrosion inhibitor film before being placed in reinforced wooden crates, which are filled with cushioning materials and equipped with impact-resistant corner protectors; copper tubes and rods are sealed with plastic end caps, wrapped with PE protective film, and then layered into steel-frame logistics containers, with EPE pearl cotton separating each layer; copper wires are automatically wound onto spools, vacuum-sealed, covered with waterproof film, and secured on customized iron-wood pallets; copper strips are wrapped with non-woven fabric, coiled onto high-strength steel cores, and placed into waterproof composite material coils with desiccants inside. All packaging passes ISTA-3A transport testing, and the outer boxes are labeled with international hazardous material identifiers, moisture warnings, and scannable logistics codes, ensuring the cargo withstands moisture, impact, and chemical erosion during global transportation.

Get Fast Quote & Logistics Plan







